Need advice concerning clocking

[flexible_hold]

Hi i have a computer thats a bit old, upgraded bits here and there, and i was woundering if i could get some advice regarding how much i can do to it to make it better "clocking it not buying things" Because if i cant get it 500 mhz better atleast, im buying new hardware but that will take a while so, any advice would be appriciated. Currently using Artic cooling L2 on 3000 rpm for cpu coolant.

 

 

Processors Information

 

Processor 1 (ID = 0)

Number of cores 1

Number of threads 1 (max 1)

Name AMD Athlon XP

Codename Thoroughbred

Specification AMD Athlon XP 2400+

Package Socket A (462)

CPUID 6.8.1

Extended CPUID 7.8

Core Stepping B0

Technology 0.13 um

Core Speed 2020.1 MHz (15.0 x 134.7 MHz)

Rated Bus speed 269.3 MHz

Instructions sets MMX (+), 3DNow! (+), SSE

L1 Data cache 64 KBytes, 2-way set associative, 64-byte line size

L1 Instruction cache 64 KBytes, 2-way set associative, 64-byte line size

L2 cache 256 KBytes, 16-way set associative, 64-byte line size

FID/VID Control no

Features

K7 Thermal sensor yes

 

Chipset

////////////////////////////////////

Northbridge SiS 741GX rev. 03

Southbridge SiS LPC Bridge rev. 25

Graphic Interface AGP

AGP Revision 3.0

AGP Transfer Rate 8x

AGP SBA supported, enabled

Memory Type DDR

Memory Size 768 MBytes

CAS# 2.5

RAS# to CAS# 3

RAS# Precharge 3

Cycle Time (tRAS) 6

Bank Cycle Time (tRC) 9

 

DIMM #1

////////////////////////////////////

General

Memory type DDR

Manufacturer (ID) Melco (7F7F7F8300000000)

Size 256 MBytes

Max bandwidth PC2100 (133 MHz)

Number of banks 1

Data width 64 bits

Nominal Voltage 2.50 Volts

Timings table

Frequency (MHz) 100 133

CAS# 2.0 2.5

RAS# to CAS# delay 2 3

RAS# Precharge 2 3

TRAS 5 6

 

DIMM #2

////////////////////////////////////

General

Memory type DDR

Manufacturer (ID) Kingston (7F98000000000000)

Size 512 MBytes

Max bandwidth PC2100 (133 MHz)

Number of banks 2

Data width 64 bits

Nominal Voltage 2.50 Volts

 

Timings table

Frequency (MHz) 100 133

CAS# 2.0 2.5

RAS# to CAS# delay 2 3

RAS# Precharge 2 3

TRAS 5 6

 

Hardware monitor

////////////////////////////////////

Winbond W83697HF hardware monitor

 

Voltage sensor 0 1.65 Volts [0x67] (CPU VCore)

Voltage sensor 1 3.23 Volts [0xCA] (AUX)

Voltage sensor 2 2.90 Volts [0xB5] (+3.3V)

Voltage sensor 3 5.05 Volts [0xBC] (+5V)

Voltage sensor 4 12.71 Volts [0xD1] (+12V)

MOTHERBOARD HEAT 35°C (94°F) [0x23] (TMPIN0)

CPU HEAT 43°C (109°F) [0x56] (TMPIN1)

Fan sensor 1 3013 RPM [0x38] (FANIN1)

 

DMI BIOS

////////////////////////////////////

vendor American Megatrends Inc.

version P1.90

 

DMI System Information

////////////////////////////////////

manufacturer American Megatrends Inc.

product K7S41GX

version 1.0

 

DMI Processor

////////////////////////////////////

manufacturer AMD

model AMD Athlon XP 2400+

clock speed 2000.0MHz

FSB speed 133.0MHz

multiplier 15.0x

 

DMI Memory Controller

////////////////////////////////////

correction 32-bit ECC

Max module size 128MBytes

Endret 18. september 2007 av flexible_hold

[TrooperTom]

You could start by trying to increase the fsb by 5 mhz at a time.

I dont think you have much to gain by tampering with the RAM speed or timings.

I hear the fat lady singing for that putter mate :-P

Endret 19. september 2007 av TrooperTom

[flexible_hold]

You could start by trying to increase the fsb by 5 mhz at a time.

I dont think you have much to gain by tampering with the RAM speed or timings.

I hear the fat lady singing for that putter mate :-P

9527075[/snapback]

 

ye did that, think it wouldnt start straight after 200 mhz, what is it then if the computer wont start then when i try start it i get cmos error? xD fixed that after i took the battery out but what is that:P?