Debian fryser eller internett slutter a virke.

[Ståle]

Har satt opp brannmur pa Debian maskinen min.

 

Den er inni et lite skap. Men temp ser greie ut:

 

debian:~# mbmon -r

TEMP0 : 37.6

TEMP1 : 32.1

TEMP2 : 23.3

 

Det er en 600MHz PII CPU

 

Den virker helt fint, men bare i 2 dager. Sa klikker den/laser seg. Hvilken logfil skal jeg sjekke ut?

Endret 19. august 2007 av Ståle

[Del]

Kan være tricky å finne ut av (du må jo vente et par dager for å reprodusere problemet). Jeg ville vel aller først kjørt en mem-check, råtten ram er hyppigste synder. Jeg antar naturligvis at det er Etch evt. Sarge du kjører. Dernest er råtne drivere til hardware neste punkt, burde kunne sjekkes ved litt googling. Sjekk dmesg:

http://en.wikipedia.org/wiki/Dmesg

Hvis ingen av disse gir deg noe, så ville jeg begynt å prøve å isolere applikasjoner. Det meste kan man jo slå av, kjernen kan du jo skifte ut en periode. Kan være at du er rammet av en bug, men dette er jo svært sjelden i Debian stable.

[Ståle]

dmesg | tail

 

 

debian:~# dmesg | tail

RPC: failed to contact portmap (errno -101).

eth0: no IPv6 routers present

eth3: no IPv6 routers present

ip_tables: © 2000-2006 Netfilter Core Team

Netfilter messages via NETLINK v0.30.

ip_conntrack version 2.4 (2047 buckets, 16376 max) - 224 bytes per conntrack

eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

eth3: link up, 100Mbps, full-duplex, lpa 0x41E1

eth0: no IPv6 routers present

eth3: no IPv6 routers present

 

 

 

 

 

dmesg

 

 

 

debian:~# dmesg

Linux version 2.6.18-5-686 (Debian 2.6.18.dfsg.1-13etch1) ([email protected]) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Sun Aug 12 21:57:02 UTC 2007

BIOS-provided physical RAM map:

BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)

BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)

BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)

BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)

BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)

BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)

BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)

0MB HIGHMEM available.

255MB LOWMEM available.

On node 0 totalpages: 65520

DMA zone: 4096 pages, LIFO batch:0

Normal zone: 61424 pages, LIFO batch:15

DMI 2.1 present.

ACPI: RSDP (v000 VIA694 ) @ 0x000f6f80

ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3000

ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3040

ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000

ACPI: PM-Timer IO Port: 0x4008

Allocating PCI resources starting at 20000000 (gap: 10000000:efff0000)

Detected 601.415 MHz processor.

Built 1 zonelists. Total pages: 65520

Kernel command line: root=/dev/hdc1 ro

Local APIC disabled by BIOS -- you can enable it with "lapic"

mapped APIC to ffffd000 (01209000)

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Initializing CPU#0

PID hash table entries: 1024 (order: 10, 4096 bytes)

Console: colour VGA+ 80x25

Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

Memory: 252220k/262080k available (1541k kernel code, 9332k reserved, 576k data, 196k init, 0k highmem)

Checking if this processor honours the WP bit even in supervisor mode... Ok.

Calibrating delay using timer specific routine.. 1204.38 BogoMIPS (lpj=2408774)

Security Framework v1.0.0 initialized

SELinux: Disabled at boot.

Capability LSM initialized

Mount-cache hash table entries: 512

CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000

CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000

CPU: L1 I cache: 16K, L1 D cache: 16K

CPU: L2 cache: 256K

CPU serial number disabled.

CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#0.

Compat vDSO mapped to ffffe000.

Checking 'hlt' instruction... OK.

SMP alternatives: switching to UP code

Freeing SMP alternatives: 12k freed

ACPI: Core revision 20060707

ACPI: setting ELCR to 0200 (from 0e00)

CPU0: Intel Pentium III (Coppermine) stepping 01

SMP motherboard not detected.

Local APIC not detected. Using dummy APIC emulation.

Brought up 1 CPUs

migration_cost=0

checking if image is initramfs... it is

Freeing initrd memory: 4409k freed

NET: Registered protocol family 16

ACPI: bus type pci registered

PCI: PCI BIOS revision 2.10 entry at 0xfb0e0, last bus=1

PCI: Using configuration type 1

Setting up standard PCI resources

ACPI: Interpreter enabled

ACPI: Using PIC for interrupt routing

ACPI: PCI Root Bridge [PCI0] (0000:00)

PCI: Probing PCI hardware (bus 00)

ACPI: Assume root bridge [\_SB_.PCI0] bus is 0

PCI quirk: region 6000-607f claimed by vt82c686 HW-mon

PCI quirk: region 5000-500f claimed by vt82c686 SMB

Boot video device is 0000:01:00.0

ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]

ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9

ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)

ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)

ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *9

Linux Plug and Play Support v0.97 © Adam Belay

pnp: PnP ACPI init

pnp: PnP ACPI: found 13 devices

PnPBIOS: Disabled by ACPI PNP

PCI: Using ACPI for IRQ routing

PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report

PCI: Bridge: 0000:00:01.0

IO window: disabled.

MEM window: d0000000-d3ffffff

PREFETCH window: d4000000-d4ffffff

PCI: Setting latency timer of device 0000:00:01.0 to 64

NET: Registered protocol family 2

IP route cache hash table entries: 2048 (order: 1, 8192 bytes)

TCP established hash table entries: 8192 (order: 4, 65536 bytes)

TCP bind hash table entries: 4096 (order: 3, 32768 bytes)

TCP: Hash tables configured (established 8192 bind 4096)

TCP reno registered

audit: initializing netlink socket (disabled)

audit(1187512641.944:1): initialized

VFS: Disk quotas dquot_6.5.1

Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

Initializing Cryptographic API

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered (default)

PCI: Disabling Via external APIC routing

isapnp: Scanning for PnP cards...

isapnp: No Plug & Play device found

Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled

serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A

00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A

RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize

PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12

serio: i8042 AUX port at 0x60,0x64 irq 12

serio: i8042 KBD port at 0x60,0x64 irq 1

mice: PS/2 mouse device common for all mice

TCP bic registered

NET: Registered protocol family 1

NET: Registered protocol family 17

NET: Registered protocol family 8

NET: Registered protocol family 20

Using IPI No-Shortcut mode

ACPI: (supports S0 S1 S3 S4 S5)

Freeing unused kernel memory: 196k freed

Time: tsc clocksource has been installed.

input: AT Translated Set 2 keyboard as /class/input/input0

ACPI: CPU0 (power states: C1[C1] C2[C2])

ACPI: Processor [CPU0] (supports 2 throttling states)

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2

ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx

usbcore: registered new driver usbfs

usbcore: registered new driver hub

USB Universal Host Controller Interface driver v3.0

ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11

PCI: setting IRQ 11 as level-triggered

ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11

PCI: VIA IRQ fixup for 0000:00:07.2, from 9 to 11

uhci_hcd 0000:00:07.2: UHCI Host Controller

uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1

uhci_hcd 0000:00:07.2: irq 11, io base 0x0000c400

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 2 ports detected

8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)

ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11

PCI: VIA IRQ fixup for 0000:00:07.3, from 9 to 11

uhci_hcd 0000:00:07.3: UHCI Host Controller

uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2

uhci_hcd 0000:00:07.3: irq 11, io base 0x0000c800

usb usb2: configuration #1 chosen from 1 choice

hub 2-0:1.0: USB hub found

hub 2-0:1.0: 2 ports detected

8139cp 0000:00:0a.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip

8139cp 0000:00:0a.0: Try the "8139too" driver instead.

8139cp 0000:00:0b.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip

8139cp 0000:00:0b.0: Try the "8139too" driver instead.

VP_IDE: IDE controller at PCI slot 0000:00:07.1

PCI: VIA IRQ fixup for 0000:00:07.1, from 255 to 0

VP_IDE: chipset revision 6

VP_IDE: not 100% native mode: will probe irqs later

VP_IDE: VIA vt82c686a (rev 1b) IDE UDMA66 controller on pci0000:00:07.1

ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:pio, hdb:DMA

ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:DMA, hdd:DMA

Probing IDE interface ide0...

8139too Fast Ethernet driver 0.9.27

Time: acpi_pm clocksource has been installed.

hdb: IDE/ATAPI CD-ROM 50XS, ATAPI CD/DVD-ROM drive

ide0 at 0x1f0-0x1f7,0x3f6 on irq 14

Probing IDE interface ide1...

hdc: IBM-DTLA-307030, ATA DISK drive

hdd: IBM-DTLA-307030, ATA DISK drive

ide1 at 0x170-0x177,0x376 on irq 15

ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10

PCI: setting IRQ 10 as level-triggered

ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10

eth0: RealTek RTL8139 at 0xdc00, 00:0e:2e:31:25:a4, IRQ 10

eth0: Identified 8139 chip type 'RTL-8100B/8139D'

ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11

ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11

eth1: RealTek RTL8139 at 0xe000, 00:0a:cd:07:de:4f, IRQ 11

eth1: Identified 8139 chip type 'RTL-8100B/8139D'

hdc: max request size: 128KiB

hdb: ATAPI 11X CD-ROM drive, 128kB Cache, UDMA(33)

Uniform CD-ROM driver Revision: 3.20

hdc: 60036480 sectors (30738 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(66)

hdc: cache flushes not supported

hdc: hdc1 hdc2 < hdc5 >

hdd: max request size: 128KiB

hdd: 60036480 sectors (30738 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(66)

hdd: cache flushes not supported

hdd: hdd1

Attempting manual resume

EXT3-fs: INFO: recovery required on readonly filesystem.

EXT3-fs: write access will be enabled during recovery.

kjournald starting. Commit interval 5 seconds

EXT3-fs: hdc1: orphan cleanup on readonly fs

ext3_orphan_cleanup: deleting unreferenced inode 1062889

ext3_orphan_cleanup: deleting unreferenced inode 1062888

ext3_orphan_cleanup: deleting unreferenced inode 1062887

ext3_orphan_cleanup: deleting unreferenced inode 1062886

ext3_orphan_cleanup: deleting unreferenced inode 1062885

EXT3-fs: hdc1: 5 orphan inodes deleted

EXT3-fs: recovery complete.

EXT3-fs: mounted filesystem with ordered data mode.

Linux agpgart interface v0.101 © Dave Jones

Real Time Clock Driver v1.12ac

agpgart: Detected VIA Apollo Pro 133 chipset

agpgart: AGP aperture is 4M @ 0xd5000000

parport_pc: VIA 686A/8231 detected

parport_pc: probing current configuration

parport_pc: Current parallel port base: 0x378

parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]

parport_pc: VIA parallel port: io=0x378, irq=7

pci_hotplug: PCI Hot Plug PCI Core version: 0.5

input: PC Speaker as /class/input/input1

shpchp: Standard Hot Plug PCI Controller Driver version: 0.4

FDC 0 is a post-1991 82077

input: ImPS/2 Generic Wheel Mouse as /class/input/input2

ts: Compaq touchscreen protocol output

ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11

PCI: Setting latency timer of device 0000:00:07.5 to 64

Adding 755012k swap on /dev/hdc5. Priority:-1 extents:1 across:755012k

EXT3 FS on hdc1, internal journal

loop: loaded (max 8 devices)

device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: [email protected]

NET: Registered protocol family 10

lo: Disabled Privacy Extensions

IPv6 over IPv4 tunneling driver

ACPI: Power Button (FF) [PWRF]

ACPI: Power Button (CM) [PWRB]

lp0: using parport0 (interrupt-driven).

ppdev: user-space parallel port driver

eth3: link up, 100Mbps, full-duplex, lpa 0x41E1

eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

NET: Registered protocol family 5

Installing knfsd (copyright © 1996 [email protected]).

NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory

NFSD: starting 90-second grace period

portmap: RPC call returned error 101

RPC: failed to contact portmap (errno -101).

portmap: RPC call returned error 101

RPC: failed to contact portmap (errno -101).

portmap: RPC call returned error 101

RPC: failed to contact portmap (errno -101).

eth0: no IPv6 routers present

eth3: no IPv6 routers present

ip_tables: © 2000-2006 Netfilter Core Team

Netfilter messages via NETLINK v0.30.

ip_conntrack version 2.4 (2047 buckets, 16376 max) - 224 bytes per conntrack

eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

eth3: link up, 100Mbps, full-duplex, lpa 0x41E1

eth0: no IPv6 routers present

eth3: no IPv6 routers present

 

 

[Del]

Det eneste tegnet jeg så der var at filsystemet så ut til å ha hatt en hard reboot, så den krasjet vel før du bootet nå?

 

Har du sjekket minnet?

 

Dersom du også har gjort noen kontrollrunder på drivere, eller kanskje du allerede mistenker en applikasjoner, så kan strace være et kraftig verktøy for å følge en applikasjon frem mot en krasj:

http://en.wikipedia.org/wiki/Strace

Endret 19. august 2007 av Del

[Ståle]

Ja

 

Skal ta a sjekke memtest i natt. Sosteren min liker ikke a vaere uten internett

 

Oppdaterte linux imaget rett etter jeg fikk internett til a funke.

[Ståle]

Altsa:

Installerte Debian -> alt virket fint -> oppdaterte alt -> 2 dager senere klikker det -> rebooter -> 2 dager senere klikker det ->

na stopper bare internett a virke, sa at maskinen fremdeles kunne sla pa/av numlock, men finner ikke ut a fa det til a virke igjen -> reboot

 

 

 

 

der har datamaskinen statt uten gdm i 1 dag.

Endret 19. august 2007 av Ståle

[Del]

OK, da høres det ut som problemet er rimelig godt isolert (for du kjørte vel mem-test?). Her har du en tråd hvor enkelte andre har hatt samme problem, og det ser ut til at alle fikk løst det på litt forskjellig vis:

http://www.linuxquestions.org/questions/sh...ad.php?t=162896

Dersom du ønsker å isolere feilen ytterligere kan du jo sjekke ut hvilken IDE kontroller som sitter på hovedkortet ditt:

$ lspci

og google litt etter om noen har opplevd problemer med den. Dersom det er driverproblem, så burde du finne det da.

Endret 20. august 2007 av Del

[Ståle]

Den tok jeg ikke helt.

[Ståle]

Ja, tok memtest under boot. Og ingen feil.

 

Diskene ja. Det kan det vaere. Har 2 disker. De var i Raid 0 helt til den ene krasjet. Vet ikke hvorfor. Ma ha satt feil disk i maskinen da.

 

*finne ny disk*

[Ståle]

Er det mulig a kopiere hele disken til en annen disk. Slik at jeg ikke ma installere alt pa nytt?

[Sokkalf™]

Dersom du har en helt lik disk kan du klone den slik (funker også om target-disken er litt større, men du må resize partisjoner etc etterpå) :

dd if=/dev/hda of=/dev/hdb

 

Der /dev/hda er disken du skal kopiere, og /dev/hdb er disken du kopierer til.

 

Edit: Dette bør du gjøre mens disken er unmounta, evt. gjøre det fra en livecd e.l om det er root-filsystemet du skal kopiere.

Endret 20. august 2007 av Sokkalf^