555
-
Innlegg
1 024 -
Ble med
-
Besøkte siden sist
Innholdstype
Profiler
Forum
Hendelser
Blogger
Om forumet
Innlegg skrevet av 555
-
-
-
Knerta en Athlon 1,33 når jeg skulle montere en orb kjøler
Knerta en xp 1600+(pal 2GHz) når jeg fikla med kompressor kjøler
Svidde Radeon VE kortet mitt når det tilfeldigvis lå en kjøleribbe på det :wink:
Gf3 kortet mitt klokka jeg til døde
-
har du/dere noen tips til meg om loddingen på selve chip-pinnene før jeg begynner?
Først fortinner du ledningen du skal lodde så legger du den inntil benet på chipen deretter tar du loddebolten og varmer ledningen til den sitter. OBS ikke hold loddebolten inntil mere en noen sekunder! det er nok.
-
gjør det noe om det kommer litt tinn på de andre pinnene, hvis det ikke har kontakt med noe annet enn de burde?
På spenningsregulatoren? så lenge det ikke er kontakt steder det ikke skal være det gjør det ingen ting
-
Det kan ikke være at du har flere komponenter på samme interrupt request (IRQ) da?
Jeg har samme problem, kjøpte nettopp Herkules 3D Prophet 9800 pro men jeg dropper fortsatt i cs. Så tok jeg en titt på device manager og fant ut at grafikk kortet delte samme IRQ som lyd kortet, nettverks kortet og USB portene. Nå har ikke jeg så veldig peil men når jeg deaktiverte lydkortet og nettverkskortet løp jeg rundt i lan game med 100fps=) noe som ikke funka etter deaktiveringen. Feks lage et lan game med map de_aztec, gå ut på b1 og se ned i vannet. Her fikk jeg 50fps, helt til jeg deaktiverte=) Flax at mitt hk har alle pci portene og agp porten på samme IRQ.
Jeg byttet hk og innstalert win på nytt for noen dager siden og har etter det hatt fps dropp som F.. (i CS) men når jeg så posten din sjekket jeg irq'ene mine og fant ut at net.kort, lydkort og skjermkort var på samme!(irq12)
Etter jeg hadde lett etter en måte å skifte irq fant jeg i BIOS'en et sted jeg kunne reservere irq for ISA.
Jeg reserverte irq12 og så fikk kortene nye og jeg 100FPS
-
Alle Radeon kort kan bruke samme catalyst driver www.ati.com
-
slik bryteren står nå, er den på eller av?
Tror av
-
Ser greit ut det.
Men når jeg voltmodder hk pleier jeg å ta jord fra et av skrue festene på hk(men jord er jord!).
-
clonecd
-
er det bare meg som håpet at viruset greide å oppdatere seg selv?
Er litt skuffet ja
-
-
Har aldri hør om dette før men...
Western Digitals hårddiskar fungerar ej tillfredställande med moderkort som har nForce2-chipset. Detta fel yttrar sig på Western-diskar med varierande firmware-version, det går därför ej entydigt att peka på specifika modeller. Det kan alltså fungera i vissa fall, men risken att det inte gör det är för stor för att vi skall kunna rekommendera denna kombination. Ovanstående gäller även moderkort med VIA KT133A och 686B chipsets -
Duron [email protected] 1,2V Alu kjøler uten vifte. Temp: ca. 60+-5C etter CS
-
Så det er slik at vha potmeteret kan man gi VLc mellom 0V og 5V?
Ja, tror det.
(Hvis vi går ut ifra at VLc er jord)
-
På tegningen er det koblet 0V på nederste ben på potmeteret og 5V på øverste. det midterste benet kan justeres opp og ned.(tenk et skyvepotmeter
(er ikke sikker på hva det heter))Slik det er koblet kan du ta ut mellom 0 og 5V.
RETT MEG HVIS JEG TAR FEIL!
-
Jeg har to skjermer og ser spill på ene og win på andre. Men di fleste spill minimerer seg når jeg trykker på desktopen
-
Jeg anbefaler deg til å kontakte produsenten av kortet og spørre dem hvilken del det er og om dem kan skaffe den (hvis ikke elfa har den da).
-
Min første vannkjøler var en TT ORB kjøler med kobber kjerne som jeg borret vann kanaler i og beholdt orginal vifta.
Og det funket bra?
Helt OK som vannkjøler men den var aldri noe spesielt god luftkjøler(t-bird 1.4@45-60C).
-
I'm posting this because I think everyone needs to be a bit more aware
that a so called "bad flash" does no necessarily mean a trashed BIOS
chip or a hosed motherboard. I'm sure the more experienced computer
builders are aware of this....so this post is aimed at the less
computer savvy or the people that just plain didn't know.
YES, flashing your BIOS is risky....it can go bad for any number of
reasons.
NO, you shouldn't flash unless the new version includes something that
is truly needed.
But if you just have to have the newest software,drivers,BIOS as soon
as its released, and I'm included, then you need to know that there is
a good chance that an "OHH SHIT" situation can turn into a "WHEWWW"
AWARD BIOS' are "bootblock" BIOS'...basically what this means is that
there is a portion of the BIOS that is reserved and unwritten to (most
of the time) that allows rudamentary hardware accessability(eg.floppy,
ISA, Keyboard) in the event that the BIOS becomes corrupted in some
way as to prevent the system from POSTing normally.
First off, if you think the flash went bad, try clearing the CMOS. I
know this sounds generic, but it is sometimes all that is needed as
the flash may have wreaked havoc upon the settings as to not allow the
system to POST...and not actually corrupted the BIOS itself.
Sometimes, if your lucky, holdind down the INSERT key while powering
up the system will get it to POST normally as it resets certain
settings to default. I actually saw someone mention this in a
thread...good job...not alot of people are aware of this ability to
"force" the system to POST. If these fail, your looking at a true "bad
flash" scenario.
As I said before, the "bootblock" allows access to to floppy, ISA, and
keyboard input. If your lucky enough to have a board with an ISA slot
(doubtful) and an old ISA vid card laying around, the recovery process
is easy, as you will be able to see what your doing on the screen. I
don't think any of SOYO's current boards have an ISA slot so it is
more of a challenge as everything has to be automated and done blind.
Let me say this. If you get ANY beep codes at startup and the floppy
light comes on and appears to initialize, your chances of recovering
are VERY high, regardless of whether or not the system appears to do
anything else. If you don't have a floppy...well...send the BIOS chip
off to get reprogrammed, or buy a new one...because there is nothing
you can do.
OBVIOUSLY YOU NEED ACCESS TO ANOTHER COMPUTER FOR THESE NEXT STEPS
BECAUSE YOURS IS OUT TO LUNCH RIGHT NOW
1.) You need to make a bootable floppy. The best way to do this is to
go to www.bootdisk.com and download DrDOS...but you want the one "for
flashing" as it has no drivers or any unesessary files with it. It's
just "pure" DOS. Just click on the downloaded file and it will prompt
you to place a floppy in the drive and will create the boot floppy for
you.
2.) Place "awdflash.exe" and whatever BIOS your flashing (ex.
123abc.bin) on the bootable floppy you created.
3.) Now you need to create an autoexec.bat file. This is what
automates the entire process since it's being done "blind". To do
this, all you need is a text editor, notepad being the easiest. Just
open notepad and type "awdflash 123abc.bin /py /sn /Sb /cd /cp /cc /R"
without the quotes. Make sure you fill in the "123abc.bin" with the
correct filename...this is just an example. It should look like this:
awdflash 123abc.bin /py /sn /Sb /cd /cp /cc /R
Make sure there is a space between awdflash and you BIOS file and
after your BIOS file and between all switches. Now save what you
created here in notepad on your floppy as autoexec.bat
Basically what this does is it automatically loads awdflash, inserts
the BIOS file, and....
/py - program yes
/sn - save no
/Sb - skips rewriting the bootblock
/cd /cp /cc - resets all configuration data and clears CMOS
/R - restarts the system when complete
4.) Once you have this floppy complete it's time to put it in the
drive, power the system up, and cross your fingers. Just keep your
eyes on the floppy and HDD light and keep an ear out. It only takes a
minutes or so to complete so you have to be ready to remove the floppy
when the system restarts (you should be able to tell when all
lights and activity stop, pause for a few moments and then restarts).
At this point, if all went well, your system should POST. You can now
go into your setup, make your needed changes, and bingo...your back in
business.
WELL...thats pretty much it. I hope this helps some people. This isn't
100% quaranteed to work. Some "bad flashes" just can't be recovered
from, but it has worked for me in the past.
Good Luck,
Cappy
JUST A FEW NOTES:
NO...I don't work for SOYO, but I figured this info might save some
people some headaches....and money. I think this info might be on
their site, with less detail and minus some of "awdflash's" switches
that really should be included.
Also, even if you don't have to use this proceedure, If your going to
flash your BIOS, it's good to make this floppy anyway...just in case.
And finally, this is only for AWARD BIOS'. AMI BIOS' use a different
recovery proceedure.....It's WAY easier.
-
"Advarsel" - ikonet er uansett en midlertidig løsning for å holde rede på om brukere har blitt advart for noe.
Da setter dere vel ikke pris på denna avataren da? :wink:
-
Min første vannkjøler var en TT ORB kjøler med kobber kjerne som jeg borret vann kanaler i og beholdt orginal vifta.
-
-
www.3dfxcool.no har denna
-
Settlers 4
Grafikkortguiden.Kjøpe nytt kort?Se her før du lager ny post
i Skjermkort
Skrevet
Hvor har du dette fra?
Jeg finner ingen 9100 kort som kjører mer en 250/250MHz.