smartctl 5.42 2011-10-20 r3458 [x86_64-linux-3.1.0-1.2-desktop] (SUSE RPM) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Green Device Model: WDC WD10EACS-00ZJB0 Serial Number: WD-WCASJ1576619 LU WWN Device Id: 5 0014ee 2ac0e58c3 Firmware Version: 01.01B01 User Capacity: 1 000 204 886 016 bytes [1,00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Fri Nov 25 16:34:09 2011 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (27960) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 255) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 194 193 051 Pre-fail Always - 8547 3 Spin_Up_Time 0x0003 178 174 021 Pre-fail Always - 8075 4 Start_Stop_Count 0x0032 096 096 000 Old_age Always - 4156 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x000e 200 200 051 Old_age Always - 0 9 Power_On_Hours 0x0032 080 080 000 Old_age Always - 15027 10 Spin_Retry_Count 0x0012 100 100 051 Old_age Always - 0 11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 647 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 134 193 Load_Cycle_Count 0x0032 172 172 000 Old_age Always - 86019 194 Temperature_Celsius 0x0022 127 097 000 Old_age Always - 25 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 200 198 000 Old_age Always - 7 198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 100 253 051 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 4871 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 4871 occurred at disk power-on lifetime: 15023 hours (625 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 b8 95 3d 40 Error: UNC at LBA = 0x003d95b8 = 4036024 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 d0 08 b8 95 3d 1d 00 02:36:40.745 READ VERIFY SECTOR(S) EXT 42 d0 08 b8 95 3d 1d 00 02:36:36.833 READ VERIFY SECTOR(S) EXT 42 d0 08 b8 95 3d 1d 00 02:36:32.798 READ VERIFY SECTOR(S) EXT 42 d0 08 b8 95 3d 1d 00 02:36:28.886 READ VERIFY SECTOR(S) EXT 42 d0 08 b8 95 3d 1d 00 02:36:24.839 READ VERIFY SECTOR(S) EXT Error 4870 occurred at disk power-on lifetime: 15023 hours (625 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 b8 95 3d 40 Error: UNC at LBA = 0x003d95b8 = 4036024 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 d0 08 b8 95 3d 1d 00 02:36:36.833 READ VERIFY SECTOR(S) EXT 42 d0 08 b8 95 3d 1d 00 02:36:32.798 READ VERIFY SECTOR(S) EXT 42 d0 08 b8 95 3d 1d 00 02:36:28.886 READ VERIFY SECTOR(S) EXT 42 d0 08 b8 95 3d 1d 00 02:36:24.839 READ VERIFY SECTOR(S) EXT 42 d0 08 b0 95 3d 1d 00 02:36:24.839 READ VERIFY SECTOR(S) EXT Error 4869 occurred at disk power-on lifetime: 15023 hours (625 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 b8 95 3d 40 Error: UNC at LBA = 0x003d95b8 = 4036024 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 d0 08 b8 95 3d 1d 00 02:36:32.798 READ VERIFY SECTOR(S) EXT 42 d0 08 b8 95 3d 1d 00 02:36:28.886 READ VERIFY SECTOR(S) EXT 42 d0 08 b8 95 3d 1d 00 02:36:24.839 READ VERIFY SECTOR(S) EXT 42 d0 08 b0 95 3d 1d 00 02:36:24.839 READ VERIFY SECTOR(S) EXT 42 d0 08 98 94 3d 1d 00 02:36:20.682 READ VERIFY SECTOR(S) EXT Error 4868 occurred at disk power-on lifetime: 15023 hours (625 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 b8 95 3d 40 Error: UNC at LBA = 0x003d95b8 = 4036024 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 d0 08 b8 95 3d 1d 00 02:36:28.886 READ VERIFY SECTOR(S) EXT 42 d0 08 b8 95 3d 1d 00 02:36:24.839 READ VERIFY SECTOR(S) EXT 42 d0 08 b0 95 3d 1d 00 02:36:24.839 READ VERIFY SECTOR(S) EXT 42 d0 08 98 94 3d 1d 00 02:36:20.682 READ VERIFY SECTOR(S) EXT 42 d0 08 98 94 3d 1d 00 02:36:16.825 READ VERIFY SECTOR(S) EXT Error 4867 occurred at disk power-on lifetime: 15023 hours (625 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 08 b8 95 3d 40 Error: UNC at LBA = 0x003d95b8 = 4036024 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 42 d0 08 b8 95 3d 1d 00 02:36:24.839 READ VERIFY SECTOR(S) EXT 42 d0 08 b0 95 3d 1d 00 02:36:24.839 READ VERIFY SECTOR(S) EXT 42 d0 08 98 94 3d 1d 00 02:36:20.682 READ VERIFY SECTOR(S) EXT 42 d0 08 98 94 3d 1d 00 02:36:16.825 READ VERIFY SECTOR(S) EXT 42 d0 08 98 94 3d 1d 00 02:36:12.935 READ VERIFY SECTOR(S) EXT SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.